Just got it yesterday so I’m still playing with it. Has a Hexium 300 on it. Stock setup will eventually be switched to a thin folding stock 2.0.

- M400 Tread
- P211 GTO
- P365 XMacro Comp
- P320 Flux Raider
- P320 M18

Any recommendations for a stock (future Sbr) and hand guard? I’ve read that a simple AR buffer tube fits on the rear, but I’d like to know if I can just throw any old tube on or if it’s a bit more complicated than that. Also would like to know how to swap the hand guard out. Thank you for any advice.

I test 3 different Duty Holsters for the P226X, Safariland, Bladetech Valor, and the Aliengear Rapid Force. Long story short is you can get all of them to work with some modifications, these are all P320 based holsters. The extended takedown lever gas pedal does not work across any of these holsters

Safariland (modified by RDR Gear)
-TLR-1 is a tight fit
-Works with XCarry to XFive
-Holosun 507-Comp does not fit with a high adapter plate
-Poor trigger guard coverage
-SAO tends to sweep off the safety on the draw

Bladetech Valor
-Needs internal modifications to work at all
-Tightest fit of the three, indexes off the Picatinny rail
-Can be run without a light
-Compatible from XCarry to X-Five
-Extended slide catch and extended magazine release will cause issues
-Hood needs modification for SAO

Aliengear Rapid Force
-Compatible from XCarry to standard X 4.4 inch but not the X-Five
-No modifications necessarily needed but the 2 below may be recommended depending on what version and model of P226X you have
-DA/SA decocker can hang up and prevent the gun from locking in
-Hood needs modification for SAO

I made a longer video that goes into detail on what modifications you need to do to make these holsters fit. Hopefully this is helpful information for folks looking to get a duty holster for their P226X.

It finally arrived!

Hey y’all, I finally took off my muzzle device yesterday, but after reassembling it’s getting caught in that position. No matter how hard I pull it won’t come out anymore, but it doesn’t always catch there which confuses me. It does feel like has more resistance in that spot when it doesn’t catch though. It’s definitely not the charging handle, I’ve quadruple checked at this point and I KNOW that it’s in its track. I really think the extractor is getting caught on something because after I get it past that sticking point it feels perfectly normal. Anyone got any advice on what to try?

I sold a bunch of pistols and rifles to try to strategize and improve my collection. I rarely succeed in making time for practice but I am determined to actually learn to shoot with the collection on the left. The right… just my 226 fetish 😻

P250 with Obsidian9

Another one for your viewing pleasure, with an included w.German slide pic for my Polack friend.

FedEx delivered my slide to wrong address that I sent off for porting so I’m guessing I won’t be getting it back. It was a Norsso Piranha C. I bought it for a pretty good deal and I’m looking for possibly replacing here soon. What would you guys buy? Considering a used Fedz 3.7” with comped slide.

Just installed today and I can’t wait to see how it feels to shoot!

Came across this used at my LGS $750. Been eyeballing the p229 for a while now. So what do the experts say?

What is a reasonable amount to pay for the WRMCX-300B-5B-R-LT-SBR whenever it is back in stock?

Installed a flat AC trigger shoe, everything else OEM. I’ve seen someone complain about this before but want to make sure I’m not going crazy here.

Looks like AC updated their previous flat trigger design to include an overtravel screw at the top rear of the trigger. That’s fine.

The issue, or maybe just a really big gripe, is that the OT screw/section of the trigger sticks out like a sore thumb, it doesn’t tuck up neatly in the module.

This looks like shit, no? None of the AC examples of this trigger show it looking like this, but most photos look like the old design with overtravel.

Am I a dumbass?

Considering a P365 for carry. What are the pros and cons of getting a comp version or not? Thx

Before I start this post, I know I’ll probably get some hate because p320, but need some advise on it.

While cleaning out the magazine well, I’m noticing some silicon residue on the inside of the grip. I’m wondering is this is something that sig intentionally did or if I can remove it. It’s where you wound put tungsten weights. Should I remove the silicon and put actual weights inside, or leave it be? Any and all advice is appreciated.

Geissele URGI
Sig 1911 scorpion

Looking to get my first Legion pistol and Im torn between the 365 AXG Legion or the 226 SA/DA Legion. Or should I wait for the 385 Legion

Just got the 17rd for my 365. I'm surprised the new mag won't allow the slide to move forward when it's empty. Have to remove, then slide will move forward. Just caught me by surprise because the 12rd slides forward with an empty mag.

Hi all, I recently ordered the Kilo3k Range finder. I have already have a dope that works accurately with StrelokPro. Is there any way to check the dope that I’ve loaded into Sig BDX before the range finder arrives? I’d hate for it to not read the same dope or is there a way to load your own data into it entirely? I can always turn off the dope from the range finder once it arrives if not accurate and use a dope card but would be a bummer for spending the money on a nicer range finder. I know I should just be patient but would probably return it if doesn’t show the same data or extremely close. (Yes I know it’s not that nice or newest but I could have spent less for a vortex)