I have two originals and they have the sliding sensation as well, but it’s more noticeable on the plus as requires less shake to feel it, just normal movement u can feel a tiny bip.

Using capsules, after a session, took capsule out to clean the mighty . Net popped out. Normal? That there are two layers of nets?. See image

Just a dead battery do you think? I've isolated the issue to the device, as the micro-usb cord is fine. I've haven't tried anything else.

I'm potentially looking at a self of third-party repair if I can understand the root cause, as legal changes in Australia have meant I likely can't seek repair with the retailer or storz. I do have my own soldering kit, but it appears the batteries are hard to come by?

Happened on two separate Mighty+ devices (second was a warrantee replacement).
Can’t upload video of the error, but partway through use, the devices performs a hard reset and flashes a square on the display. When/if it then turns back on, it’s reset to the base temp.
Onto my third Mighty+ now (second warrantee replacement), and I’d like to avoid causing the issue again, if it was even me in the first place!

I know how to pack correctly and all this. Ive used it many times. Just some batches I get do not make lots of vapor or even burns it much. It's still light brown. A type I have rn would work in a bong. Maybe a volcano. I'd rather wanna use a volcano than a bong but not sure if a volcano does the same thing if anybody knows? Anyone has this happen sometimes? I like to vape it until it's turned dark.

I got my Weezy vape today, and I’m wondering: is it necessary to do a burn-off at the maximum temperature before using it? Should the cooling unit be off the vaporizer while doing the burn-off?

Can anyone help me how to pack this in my bowl by step had never smoked dabs before

How do you all feel about the Veazy vape? I ordered one two days ago. I currently own an Arizer Solo 3, but it has been causing a sore throat, so I wanted to try something better. I also have an OG Mighty, but it is over ten years old and worn out, and I didn't want to spend as much as the Venty requires. While I like the Solo 3, it sometimes scratches my throat. In fact, I last used it two days ago and my throat still hurts.

The Solo 3 works well when I use it with a water bong, but using the Solo 3 without water filtration irritates my throat too much.

I want to experiment with Microdosing using my OG Mighty due to some interesting health benefits I have been reading about. That means tiny amounts of .05g or less every few hours. Is there any reason that simply putting .05g straight into the bowl and heating as usual is not going to work? I have done some googling on this subject and the posts all say to use capsules or a stainless steel liquid pad, but none of them say anything about reasons you shouldn’t just put small amounts of flower directly into the chamber.

As of last week the button doesn’t work anymore so need to turn on with app but it’s still chugging along lol

While I used the capsules the way S&B intended since getting my Venty, I've seen some folks on here claim that ditching the capsule leads to more airflow and a better vaping experience.

I gave it a try, and found that raw dogging it just... wasn't for me. While the airflow did seem better, manual dexterity is not my strong suit, and I found both loading and unloading the ground bud to be tedious and messy.

But then, I found my answer. The best of both worlds. And I couldn't believe how obvious it was.

Load the capsule normally, but skip the lid.

More airflow, less hassle when it comes to loading the bowl, and it's much easier to keep things clean. The perfect middle ground.

Have you tried this method? What are your thoughts?

Hi everyone, my 90 degree glass whip adapter for my orb V2 chipped. Does anyone know of a silicone replacement that won't break in the future? I'm talking about the output, not the input from my mighty. Thanks!

Edit, it's 14mm

My OG crafty (purchased March 2018) had a non functioning charging port way past warranty.
Back in September 2024 I cut a USB cable and bypassed the micro USB port by soldering directly to the board (first image)
It worked fine, but it was kind of annoying to have this way too long USB cable permanently attached to the crafty.
A few days ago I got around to it and soldered a USB C socket and thought I'd share (third image onward).

I still need to enlarge the hole in the case for the type C connector to fit inside
I need to solder 5.1KOhm on CC1 CC2 for type C to type C charging (currently, the wall side has to be type A for it to charge), might need a different USB C socket.
Some strain relief is needed for the black and red wires, maybe also replace them with more flexible wires.

I hope this is useful to somebody.

P.S. I only have 270 hours on mine, still using the original battery but I want to replace it at some point.

Anyone have any tips for a correct grind size/grinder?

Just got my first mighty, and I love it, except it seems I get so much material on the top and coming out of the pods.

I think this is a grind size issue, but could it also be a humidity issue? I keep mine with a 62 boveda

Ive never used a dry herb vaporizer once before in my life so I know its probably something I'm doing or the fact im using a prerolls weed lol but can someone help me out here?

I only have a preroll right now cause im gonna reup tomorrow, so i decided to just empty it into the vapes chamber cause i wanted to try it out but it barely produces any visible hits even with slow inhales. Could it be damaged off rip? How would I know? I just registered it on the site so I'm hoping I can warranty it if its not just the preroll weed being ground too finely.

I'm not even packing it just putting the ground bud in, it was at 409f or higher for most of my first attempt at smoking a bowl out of it, on the second i started hitting at like 200 something up to 415 and still barely got anything at all.

I just got the venty after using the crafty+ for more than 2 years. It came with the little orange thing that I find so useful but there is nowhere to put it in the venty? Am I stupid? Fuck I really liked using it and also the feeling of putting it in and out.

My mighty+ got a scratch on the ceramic chamber during first use, I used the dosing capsule but did not notice the oven screen wasn't level (factory error) when I put on the cooling unit. The cooling unit pushed the capsule down into the ceramic sidewall and caused a big scratch. Are scratches in the ceramic common and do I just ignore it now that I have flattened the screen?

I have this Mighty of a friend in front of me right now which is not charging anymore at all. Not lighting up wenn plugged in or anything but it still turns on.

Definitely not a broken charger since I have my own mighty charging with the same cord.

Removing the port probably wont work because it is glued to the pcb.

My main question is if anybody knows what places on the pcb to check to make sure if its the port or anything else?

Made the purchase last night, but I've been reading that the Venty has better airflow..

I've had a few different Pax vapes and Arizer vapes.

Should I have went with the Venty?

I used to put the dismembered head piece in a hot pot of milk, low heat for 20minutes, and then filter the galactic ember milk out of it.

Then I would pour and devide it on an ice cube tray.

lets just say I dont wanna make it through milk no more...

And that I got infinite ethanol/isopropanol in my disposal.

Which way is best to use in order to clean my headpiece and claiming all the ...reclaim ?

Ive scanned youtube and other sources, couldent find a proper tip/guide for it.

please do share your intelegence if you have any 😄

thank you and take care !

P.S

completely off-topic. but ive been using my mighty since june 2020, daily usage, up to this day. when is it finally going to die ? shuold i be worried about its battery explode ?

My crafty+ has held up strong to two years of heavy daily use, but now only lasts around 45 mins at 184C with a few boosts to 200C, which I can't complain at really.

The thing is still in warranty but I'm assuming it has clocked up too many hours to be covered? I can replace the battery myself, but am struggling to find one in the correct spec with the required tabs. Other than the very shady looking 'batteriesplus', there doesn't seem to be any UK stock. Anyone know a guy who knows a guy?

At one time, I had to solder a button on my five-year-old mighty+ and I couldn't find any information on the query "mighty+ button photos, repair", so I'll just create this thread to help people like me in the future.. TCD-C2KQR3

I think I finally found the cause of my Error 004. At least in my case, it had nothing to do with the batteries.
The problem was one of the heater wires. The heater connector has two pins: one is a solid metal pin, and the other is a small blue wire with its own terminal. That blue wire never seemed to make a very solid connection.Whenever I got Error 004, I could open the Mighty+, move that wire around or press it into the connector, and the error would disappear temporarily.

While trying to disconnect it, I accidentally broke part of the white connector, which actually worked out in my favor because it gave me access to the terminal inside. Today I got Error 004 again, so I knew exactly where to look. I soldered the blue heater wire directly to the terminal inside the connector, then put the small broken plastic piece back in place and secured it with a bit of black electrical tape to cover the opening. Everything went back together cleanly, and the error disappeared immediately.

We’ll see if it holds up long-term, but so far it looks like that loose heater wire was the real cause of my Error 004. Hopefully this helps someone else with the same issue.