Just got my p320 some big boy ports and she runs so smooth and flat 🔥🔥🔫

It’s been talked about before but I really need some help deciding which route to take. I have small hands if that matters but I need to hear your arguments for either or. If I’m not wrong, the m1823 has better ergonomics and kinda looks better BUT the Commander can reach a greater overall weight with brass panels, has a bit of customization using said panels and can take any AXG/SXG compatible magwell. I have a chance to choose, so which route should I go? I’m looking for full size steel and nothing else. Don’t like the Sig options. Yes I know one is discontinued, just answer the question.

Hey all,

I had bought a P320 and built a strike industries SMC alpha mk2 build. I still haven't shot it yet b/c I'm paranoid if I had built it properly, and I have heard (at least on mk1) that the screws that allow modularity are also a weak point for getting loose under load. Image attached shows my questions about what torque rating and what loctite, if at all, for each screw?

I could only find torque ratings online for the 4 screws on the optic mount (20 in lbs) and the alpha magwell (10 in lbs). It did ship with some blue loctite, but I am afraid of stripping and so I have some red 271 in addition to the blue 243.

Also, the screws came with some blue nylon threadlocker - I'm guessing I should remove that residue prior to loctite application?

Anyone have any experience/help? Thanks.

I am very new to shooting, so any tips would be greatly appreciated!

After going through the entire disassembly/ reassembly process I was very pleased to find that the FRT component doesn’t even remotely come close to fitting. Even with light taps of the mallet it’s not even close to moving.

Hello, just wanted some information. I just bought a compact around 2021 serial number 320 I really like it. I knew about the allegations but also knew that was the older model. According to sig this is upgraded trigger. I’ll admit ALLOT of my fellow shooters are getting in my head about them. I don’t really want to get rid of it. Do any of you guys have any thoughts or article recommendations to get out of my own head. I typically carry with one chambered. Iv been carrying a ppk/s for awhile and this was suppose to be like my upgrade lol

Lots of gucci guns in this sub. Figured I’d share a photo of my bone stock 320. This may be a sore subject but this pistol does have the “wiggle” issue and it is VERY reproducible.

I’ve owned this pistol for almost 10 years and I’m finally sending it in for the upgrade and then I’m going to do a whole bunch of work on it.

Open to suggestions for parts, I want it flat and fast. Will be going with a TXG grip mostly because I like them.

M18 slide

(Canadian legal barrel)

Eflx,

10rd mag 🤮,

Olight, (3yrs old works great)

M1811 brouwer grip milled flat and magpul 1911 grips installed

I like it thiccc

Brouwer M1823 Steel grip module

Norsso commander custom slide and bull barrel

Gideon omega 3 MOA red dot

Flat faced trigger

Sig guy internal parts kit

Springer precision extended mag release paddle

TLR-1

Had my Fuse stolen awhile back and finally finished putting this together to replace it. Wanted a range toy I could also carry and I’m loving it.

Used from a pawn shop can’t wait to shoot it. Been wanting one of these for awhile now.

Still carrying my 320. This thing is so ergonomic, it’s my favorite setup.

Can someone tell me what cut this is ?

Went to the gun store and rummaged through the used mags bin and found this 320.

The magazine was labeled .40-.357 however it absolutely fits and cycles 9mm. Is this common or an anomaly?

Got it running...500 rounds without any failures. Love shooting this set up.

I don’t normally post much of anywhere, but I figured I’d post a few pics of my EDC P320

The P320 is still the best striker fired gun on the market

i switched from a glock 19 to this and i’ve never been happier. shoots like a dream